Motor Saver 201-575-AU Fiche technique télécharger pdf (Page 48)

www.symcom.com • 800-843-8848 • fax: 605-348-5685

Available Models:

Features:

• LED status indicator

• Compact plug-in design

• DIN rail or surface mountable via octal base

pprovals:

Specications

201-100-SLD

The Model 201-100-SLD

is an 8-pin plug-in style seal-leak detector to

sense seal failures on submersible pumps. A

microcontroller-based relay that monitors the shaft

seal of a submersible pump motor. A resistive

probe is installed in the seal cavity. If water leaks

into the pump, the resistance measured by the

probe decreases. When the resistance drops below

the sensitivity setpoint, the unit will trip and the

relay contacts will change state. The unit will

automatically reset when a fault is cleared.

For more information see:

See Appendix A, page 68, Figure 8 for dimensional

drawing.

See Appendix B, page 79, Figure 41 for typical

wiring diagrams.

Auxiliary Products:

• 8-pin octal socket (P/N: CT0T08-PC)

Model 201-100-SLD

single-channel seal-leak detector, 8-pin socket mount, adjustable sensitivity point

Seal-Leak Detector

Fast Transient Burst .............................61000-4-4, Level 3, 3.5kV input

power and controls

Surge

IEC ...........................................IEC 61000-4-5, Level 3, 4kV line-to-line;

level 4, 4kV line-to-ground

ANSI/IEEE ....................................C62.41 Surge and Ring Wave Compliance

to a level of 6kV line-to-line

Hi-Potential Test ...............................Meets UL508

(2 x rated V + 1000V for 1 min.)

Safety Marks

UL (OT08-PC octal socket required) ...............UL508 (File #E68520)

CE ............................................IEC 60947-6-2

Enclosure ......................................Polycarbonate

Dimensions ....................................1.750” H x 2.375” W x 4.125” D (with socket)

(44.45 x 60.325 x 104.775mm)

Weight ........................................0.7 lb. (11.2 oz., 317.51 g)

Mounting Method ..............................DIN rail or surface mount (plug into

OT08-PC socket)

Socket Available ................................Model OT08-PC (UL Rating 600V)

The 600V socket can be surface mounted or installed on DIN Rail.

Input Characteristics

Control Voltage .................................110/120VAC nominal

Frequency .....................................50/60Hz

Functional Characteristics

Sensitivity .....................................4.7k-100kΩ

Probe Sense Voltage ............................5vdc pulsed

Output Characteristics

Output contact Rating – SPDT

Pilot Duty .....................................480VA @240VAC

General Purpose ................................10A @240VAC

General Characteristics

Ambient Temperature Range

Operating .....................................-40° to 70°C (-40° to 158°F)

Storage ........................................-40° to 80°C (-40° to 176°F)

Maximum Input Power ..........................5 W

Relative Humidity ..............................10-95%, non-condensing per IEC 68-2-3

Standards Passed

Electrostatic Discharge (ESD) .....................IEC 61000-4-2, Level 3, 6kV contact, 8kV air

Radio Frequency Immunity, Radiated .............150MHz, 10V/m

Must use Model OT08-PC or RB08-PC socket

for UL Rating!

Note: Manufacturer’s recommended screw

terminal torque for the RB Series and

OT Series Octal Sockets is 12 in.-lbs.

CATALOG_SYMCOM_2014.indd 46 6/10/14 11:06 AM

1 2 ... 43 44 45 46 47 48 49 50 51 52 53 ... 87 88

Commentaires sur ces manuels

Pas de commentaire

Motor Saver 201-575-AU Fiche technique Page 48

Commentaires sur ces manuels